Like New Pool
Request service

Independent guide. Like New Pool is an independent pool renovation and care guide, not a pool contractor. We do not perform construction, plumbing, electrical or gas work. Renovation, equipment and barrier work may require licensed professionals and permits, so check your state and local code.Like New Pool is a guide, not a pool contractor. Pool work may need licensed pros and permits, so check your local code.

  1. Home
  2. Pool leak detection

Guide 03 / Water loss

Evaporation or a leak? Find out first.

Pool Leak Detection Guide

Every pool loses water to evaporation. A leaking pool loses more, and the extra water can wash out soil, undermine a deck and quietly raise chemical costs. Start with the free test, then narrow it down.

Illustration of the waterline of a vinyl liner pool with a printed tile band

Before anyone dives with dye or pressurizes a pipe, answer one question: is the pool losing more water than a bucket of the same water sitting beside it?

Run the Bucket Test

The bucket test is the standard first step because it cancels out climate. Water in a bucket and water in the pool sit in the same sun, wind and temperature, so they should evaporate at about the same rate. If the pool drops noticeably more than the bucket, something other than evaporation is taking water.

  1. Fill a bucket with pool water to within a few inches of the top and set it on the first or second pool step, so it sits in the pool at the same temperature.
  2. Mark the water level inside the bucket, and mark the pool level on the skimmer or tile with tape or a grease pencil.
  3. Leave everything normal for 24 hours: pump on its usual schedule, auto-fill turned off, no swimming, no rain.
  4. Measure both drops in inches and compare. Then repeat with the pump off for 24 hours. A difference between pump-on and pump-off results helps point toward the pressure side or suction side of the plumbing.

Bucket test calculator

A screening aid, not a diagnosis. Rain, heavy splashing, a running auto-fill or a backwash during the test will skew the result.

Reading the pump-on and pump-off results

  • Loses more with the pump running: a leak on the pressure side (return lines, filter, valves, heater) is more likely, because those pipes are pushed outward when the pump runs.
  • Loses more with the pump off: suction-side plumbing (skimmer and main drain lines) can pull air in while running and leak out when idle.
  • Loses about the same either way: look at the shell, fittings and light niche, or stop the test with the pump off and see where the level stops dropping.
Where the level stops

With the auto-fill off and the pump off, a leaking pool often drops until it reaches the leak and then levels out. If it stops at the bottom of the skimmer opening, the skimmer is a strong suspect. If it stops at the light, look at the light niche and its cord conduit.

Usual suspects

Where Pool Leaks Usually Hide

Leaks favor joints between different materials and anything that passes through the shell. Work through them in roughly this order.

  1. 01

    Skimmer throat

    The joint where a plastic skimmer meets the concrete shell is a classic leak point, especially where deck movement or freezing has cracked the bond.

  2. 02

    Light niche and conduit

    The conduit that carries the light cord to the junction box can carry water out of the pool. Look for a gap where the cord enters the niche.

  3. 03

    Return and cleaner fittings

    Fittings set into the wall can loosen or lose their seal, and the pipe behind them can crack.

  4. 04

    Main drain

    The drain body and its pipe sit at the deepest point under the most pressure and are the hardest to reach, which is why professionals pressure test them.

  5. 05

    Buried plumbing

    Pipes under the deck can crack from settling, roots or freezing. Wet spots, sinking pavers or unusually green patches in the yard are clues.

  6. 06

    Equipment pad

    Filter lids, valve stems, pump seals and heater connections can drip. These are the easiest leaks to see, so check the pad first.

How Professional Leak Detection Works

Once the bucket test says there is a leak and the obvious spots check out, a leak detection specialist narrows it down. The methods are complementary; most jobs combine two or three.

MethodWhat it findsLimits
Dye testingLeaks at fittings, cracks, skimmer throats and light niches, by watching dye get pulled into an opening in still waterOnly works where the tester can reach and the water is calm
Pressure testingLeaks in individual plumbing lines, by plugging a line and pressurizing it to see if it holdsTells you which line leaks, not exactly where along it
Electronic listeningThe location of a leak in buried pipe or the shell, by listening for the sound of escaping water or airNeeds a quiet site and an experienced operator
Camera inspectionCracks, breaks and blockages inside pipesNeeds an access point and clear pipe

What a useful leak report looks like

Ask for a written report that lists what was tested, what passed, what failed, where the leak was found and how it was marked. Photos help. That report is what a repair contractor quotes from, and it may matter for an insurance claim.

Repair options, in general terms

Small shell and fitting leaks are often sealed with underwater putty or epoxy, or by resetting the fitting. Cracked buried pipe usually means cutting the deck and replacing a section, though some lines can be rerouted. Vinyl liner punctures can be patched; a liner leaking at many points may be due for replacement, which the resurfacing options guide covers.

Before a resurface

Find and fix leaks before applying a new finish or liner. Water escaping behind a shell can wash out soil and lead to settling, and some repairs require cutting into the very surface you just paid for.

Safety while you investigate

Keep the pool safe while the water level changes. A lowered level can expose suction fittings or make the skimmer pull air, so follow the pump maker's guidance. Never stand over or reach into an open drain or suction outlet, and see the pool safety guide for why drain covers matter.

Pool Leak Questions

How much water loss is normal for a pool?

It depends on climate, wind, sun, water temperature, heating and how much splashing goes on, so there is no single normal number. That is why the bucket test compares your pool with a bucket of the same water sitting in the same conditions instead of comparing it with a rule of thumb.

Can a pool leak through the finish itself?

Concrete shells and finishes are not perfectly waterproof, and cracks can leak. Leaks are more often found at penetrations, such as skimmers, returns, lights and main drains, and in buried plumbing.

Is dye testing safe to do myself?

Placing a small amount of pool leak dye near a suspected spot in still water is a common owner check. Turn the pump off, move slowly so you do not stir the water, and keep clear of drains and suction outlets while the system is off. Anything involving pressurizing pipes or entering the water at depth is work for a professional.

Will my insurance pay for leak detection or repair?

Coverage varies widely by policy and by cause. Read your policy or ask your agent before work starts, and keep the leak detection report, photos and invoices.

Bucket Test Says Leak?

Share your bucket test numbers, whether the loss changes with the pump on or off, and where the level stops. That detail speeds everything up.

Request leak help